Litter Robot Globe Position Fault (2024)

1. Litter-Robot 4: Red light bar with partial white flashing (Globe position)

  • If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.

  • Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.

2. Litter-Robot 3: All three lights flashing (Globe position fault)

  • Check and clear any obstructions in the waste port. Waste clumps or toys could obstruct the globe rotation and cause a globe position or over-torque fault.

  • Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!

3. Litter Robot III - Home positioning fault - RobotShop Community

4. Litter Robot 3 Home Position Fault - RobotShop Community

  • 10 feb 2021 · The Hall Effect Sensor is the sensor responsible for the tracking of the globe's position. It's what makes your Litter-Robot so intelligent.

  • Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. Would anyone have any suggestion? Thank you so much in advance for your help!

5. Litter-Robot 3: Fixing the globe magnets

6. Litter-Robot 3: Pinch contact installation guide

  • While cycling, if a potential condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly ( ...

  • Find easy steps on replacing the pinch detect terminals of your Litter-Robot 3. Visit now for a quick and smooth fix to enhance your product's efficiency.

7. Litter-Robot 4: Red with partial yellow flashing (Over-torque fault)

  • Check that your unit is not overfilled with litter. · If you recently added litter, the globe could have slowed down enough to trigger this fault. · Now, let's ...

  • Get solutions for your Litter-Robot 4 red with partial yellow flashing over-torque fault. Find easy fixes here! Explore our support page now.

8. Litter-Robot 4 Support, Troubleshooting, and Solutions

  • Our self-service troubleshooters are the fastest way to solve issues with your robot. Troubleshooter. Videos. Getting Started. Manuals. Installation Guides.

  • Need assistance with your Litter-Robot 4? Find guides & troubleshooting tips. Get the support you need today.

9. Litter-Robot 3 Support, Troubleshooting, and Solutions

  • Litter-Robot 3: All three lights flashing (Globe position fault) · Litter ... Litter-Robot 3: Red light flashing (Cat sensor fault) · Litter-Robot 3 ...

  • Have questions about your Litter-Robot 3? Get quick solutions from our dedicated support page. Start troubleshooting now.

Litter Robot Globe Position Fault (2024)

FAQs

Why is my robot litter box not detecting my cat? ›

Check for obstructions

Make sure the Litter-Robot is on a firm, level surface. The cat sensor function can be affected if the unit is on carpeting or a litter mat. Check that there are no power cords running underneath the base of the robot that might obstruct movement.

What is a pinch detect fault Litter-Robot? ›

Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat's safety while in use. These sensors monitor for potential pinch conditions at all times. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up.

How to reset Litter-Robot blinking yellow light? ›

If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful.

Can you manually cycle Litter-Robot? ›

Once you notice that your cats have used the Litter-Robot, you can cycle the unit manually by turning the unit ON. If the cats are present, it will give them a chance to observe the motion and become familiar with the sound of the Litter- Robot while you are present to reassure them.

How do you reset the litter robot 4 over torque fault? ›

Short press the Reset button, then short press the Cycle button to run a Clean cycle. After your Litter-Robot cycles, it should return to the Home position, displaying a blue light bar.

Why is my spinning globe not spinning? ›

TROUBLESHOOTING TIPS FOR NON-ROTATING MOVA GLOBE

Try placing the globe directly under a bright lamp to make sure it has adequate light to allow the light to penetrate the inner film and touch the solar cells. You can also try placing the globe by a window during a sunny day to receive indirect light.

What does motor fault mean on Litter-Robot 4? ›

Litter-Robot comes equipped with current-sensing capability to detect if the motor is connected and running properly. If the unit displays a blue and white alternating light bar, there is an issue with the motor connection, which affects the rotation of the globe.

Globe Position Fault : r/litterrobot - RedditReddithttps://www.reddit.com ›

However, I'm wondering if anyone knows where the actual sensor is? All of the troubleshooting was about cleaning out litter (issue presented on initial star...
31K subscribers in the litterrobot community. Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks.
The unit should perform an initial Clean cycle: the Globe will rotate counterclockwise to the Dump position, then rotate clockwise past the Home position to lev...

Why is my Litter-Robot not connecting? ›

Make sure bluetooth is enabled. Accept Location Services if prompted. If the app is unable to find Litter-Robot via your device's bluetooth, move your mobile device closer to your Litter-Robot, check that your mobile device's bluetooth is turned on, and the power button on your Litter-Robot is blue.

How do you fix a torque fault on a Litter-Robot? ›

Check that your unit is not overfilled with litter. If the litter is filled above the line, please remove some litter before proceeding. If you recently added litter, the globe could have slowed down enough to trigger this fault.

How do you reset the weight sensor on a litter robot 3? ›

Always remember to push the Reset button after making changes to the unit. This will recalibrate the weight sensor and circuit board to reflect the changed weight. From the Home position, press the Power button to turn the unit off. Press the Power button to turn the unit back on.

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Gov. Deandrea McKenzie

Last Updated:

Views: 5848

Rating: 4.6 / 5 (46 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Gov. Deandrea McKenzie

Birthday: 2001-01-17

Address: Suite 769 2454 Marsha Coves, Debbieton, MS 95002

Phone: +813077629322

Job: Real-Estate Executive

Hobby: Archery, Metal detecting, Kitesurfing, Genealogy, Kitesurfing, Calligraphy, Roller skating

Introduction: My name is Gov. Deandrea McKenzie, I am a spotless, clean, glamorous, sparkling, adventurous, nice, brainy person who loves writing and wants to share my knowledge and understanding with you.